1、Product composition：

RTE-2577 silicone conformal coating with epoxy siloxane as the main body, multiple copolymer copolymer and the corresponding environmental protection solvent after polymerization and grafting modification, and then supplemented by special additives, modifiers and other reactions prepared by the conformal coating.

2、use：

Widely used in thick film circuit system, porous substrate, radar, microwave radio, carrier oscilloscope transformer, printed circuit board, electronic components, cultural relics, stone carving, calligraphy and painting and other important items protection and machine protection. The product complies with IPC-CC-830, International paint safety standards and EU RoHS testing standards and is UL-94V0 certified.

3、Product performance

3.1 It can be cured at room temperature or accelerated by heating (recommended curing temperature ≤60℃);

3.2 Form a tough and wear-resistant protective layer after curing;

3.3 High insulation resistance, high breakdown voltage, arc resistance, electric spark resistance, low dielectric loss, good insulation performance;

3.4 Good temperature change resistance, cold and heat shock resistance;

3.5 Good moisture resistance, insulation and chemical resistance;

3.6 With a unique anti-counterfeiting and fluorescent tracer formula, UV indication can detect whether the coating is complete.

3.7 Good flame retardant performance, flame retardant grade reached UL94-V0 level;

3.8 Excellent boiling resistance, boiling 24h protective layer will not change, good protection performance.

4. Technical indicators

4.1 Reference Standards

The following standards contain provisions which, by reference in this standard, constitute provisions of this standard. This standard shall not be applicable to any dated reference; Any reference standard that does not indicate the date shall be the reference standard of the new version.

GB 1981-89     Test method for solvent insulating paints

GB/T 15022-94     Definitions and general requirements for solvent-free polymerizable resin composites for electrical insulation

GB/T 15023-94     Test method for solvent-free polymerizable resin composites for electrical insulation

4.2 Product Requirements

All products shall meet the requirements specified in the following table. If the Customer has additional requirements beyond the following table, special instructions shall be given in the order.

Note: The turbidity of this product is caused by the addition of defoamer, not due to water or deterioration, and will not affect the quality!

The above test results were obtained after the surface of the experimental sample was dried and then continued to cure at room temperature (25℃, 55%RH) for 168h. If the customer needs to do any type of test, it is necessary to continue to cure at room temperature (25℃, 55%RH) for 168h after the surface of the test sample is dry. If the test needs to be accelerated, it can be baked at 60℃ for 24 hours and cooled for testing. 

5. Construction methods：

5.1 Before coating, the coated parts need to be purified, clean the surface of the coated object, remove rust, dust and oil;

5.2 According to the structure and technical requirements of the pre-coated parts, the construction methods of spraying, spraying, dipping and brushing should be selected, and the application test should be done before use to make it more convenient to use, and the diluent should be reasonably used to adjust the coating viscosity according to the requirements of the coating process;

5.3 Put the covered part in the air, it can dry less than 20min at normal temperature. After the skin is formed, it is followed by the curing process from the surface to the inside. Within 24 hours (25±2℃,65±5%RH), the product will cure to a depth of 1~3mm, which can be accelerated by heating (≤60℃,65±5%RH). With the extension of time, the curing depth gradually increased to complete curing;

5.4 Based on the fast drying characteristics of the protective agent, such as dip coating or brush coating process, the paint liquid in the paint tank should be added in a small amount, and then added after use. If the viscosity increases, special thinner and fresh paint can be adjusted to the standard viscosity. If it is not expected to be used within 2 hours, pour the paint into the bucket and seal the lid.

6、Construction condition：

7、Matters needing attention：

7.1 Storage environment requirements are 5~35 ° C, relative humidity 50~80%RH dry ventilated room, away from direct sunlight, the paint should be sealed and stored in a cool, dry place, away from fire and light storage, keep good ventilation.

7.2 The paint is irritating to the skin, avoid direct contact with the skin and eyes, if contact with the skin, please wash with soapy water, if contact with the eyes, please seek medical attention in real time.

7.3 Before use or after thinning, please stir well before use.

7.4 After sizing is completed, the unfinished glue should be tightened and sealed immediately. When used again, if there is a little cleanliness in the seal, it can be removed without affecting normal use. Glue in the storage process, the container mouth may also appear a small amount of curing phenomenon, will be clear after normal use, does not affect the performance of the product. There may be a small amount of precipitation in the storage process, shake well before use, and do not affect product performance;

7.5 The product storage period is 6 months. Beyond the storage period, when the indicators are qualified, it can still be used.

8、Packaging, storage, transportation：

Iron drum sealed packaging, this product should be stored in a cool and ventilated dry place, isolated from fire, away from heat sources. The storage period is 6 months, beyond the storage period, it is necessary to re-test according to the standard provisions, if the result meets the requirements, it can still be used, the product should be transported to prevent rain, sunlight exposure, and comply with the relevant provisions of the transportation department on the transportation of hazardous chemicals.

Application field of conformal coating

Civil and Commercial

conformal coating can provide protection for electronic circuits in household appliances, making them resistant to harmful substances such as water, moisture, insects, etc. in offices and homes. It can be applied to soybean milk machine, coffee machine, Induction cooking, dryer, dishwasher, air conditioner, computer, bathroom electronics, electric car, etc.

automotive industry

The automotive industry requires conformal coating to protect circuits from the hazards of several situations, such as gasoline evaporation, salt spray, brake fluid, etc. The application of electronic systems in automobiles is constantly growing rapidly, so the use of conformal coating has become a basic requirement to ensure the long-term reliability of automotive electronic devices. For example: computer control systems, air conditioning, automotive electronics.

Aviation navigation

Due to the unique nature of the usage environment, aviation, aerospace, and navigation environments have strict requirements for electronic equipment, especially under fast pressurization and decompression conditions, good circuit performance must still be maintained. The pressure resistance stability of anti paint is therefore widely used. For example, satellite systems, military control systems, flight route control systems, navigation systems, and radar control systems.

electronic industry

conformal coating can protect electronic equipment from water, moisture, external chemicals, and special environmental erosion, ensuring its continuous stability. Its application range is very broad. For example, LED display screens, LED guardrail tubes, solar energy, instruments, power supplies, frequency converters, consumer electronics, anti-theft and fire alarm devices, etc.

Product parameters

Reminder: Support enterprise sample or personalized product customization for conformal coating users: flame retardant, temperature resistant, pressure resistant, thick coated, boiled, quick drying, fluorescent, and odor; The conformal coating meets the coating process of 20um~60um thickness. For customized requirements above 60um, you can directly contact our relevant personnel. Our company has passed the ISO: 9001 international quality management system certification, ISO: 14001 environmental management certification system, and TS: 16949 certification system. The following products comply with Chinese national standards and comply with European, American, and Japanese product standards such as IPC/JIS/UL/ROHS/REACH.

The detailed technical parameters of each product of the conformal coating can be found in its individual product introduction, and there will be no further expansion here